$24.99 - $36.99
Lightweight aluminum construction with a versatile riser bar design.
For those seeking a different take on a traditional mountain bike handlebar, the Salsa Bend Bar is available with either a 17 or 23-deg sweep, offering a more natural hand position without affecting reach or requiring the need to change your stem length. The Bend Bar swoops forward, then sweeps back to create an angled perch that’s easy to hang on to. They’re tough, strong, and durable, and great for long days bikepacking, touring, or shredding singletrack. - Constructed using double-butted, AL-7050-T76 aluminum - Bar sweeps forward, then back, to preserve stem length - 5-deg upsweep allows adjustment to suit personal preference - Bar can be flip-flopped to run up or down - Graduated ends for easy trimming - Bead-blast black finish
$79.99 - $89.99
Your favorite bars just got bigger, wider, and lighter, Go figure? The magic of 35—believe the hype! Increasing the bar diameter to 35mm allowed Race Face to shave material from the bar resulting in a dramatic reduction in overall weight while retaining the proven stiffness, strength and performance Race Face bars are known for. The ATLAS 35 bar also expands to an 800mm width (Can be trimmed down to 750mm) for hyperspeed control, can you handle it? - Proven design and durability of the Race Face Atlas bar, with increased stiffness and reduced weight of the 35mm bar platform - Requires 35mm bar clamp diameter stem - Full 800mm width that can be trimmed down to a minimum 750mm - 8 degree rearward sweep, 5 degree upward sweep
- D-shaped lightweight optimized 2014 aluminum alloy construction - Provides better "pushing" compliance for a smoother ride quality - Provides better "pulling" stiffness for cornering, sprinting, and climbing efficiency - Drop 125mm - Reach: 72mm
An ultra-lightweight 7050 aluminum trail riser bar designed for maximum singletrack shredding. - Lightweight, optimized 7075 aluminum alloy - Micro-adjust laser-etched setup markings - 35mm handlebar diameter - 9 degree rearward/ 5 degree upward sweep - 20mm rise
- D-shaped lightweight optimized 2014 aluminum alloy construction - Provides better "pushing" compliance for a smoother ride quality - Provides better "pulling" stiffness for cornering, sprinting, and climbing efficiency - Drop 125mm - Reach: 72mm - 8 degree flare
- Constructed of lightweight 2014 aluminum alloy - 35mm handlebar clamp diameter - Micro-Adjust Laser-Etched set-up markings - 20mm Rise - 9° Sweep - 5° Back-Sweep
- Clamp Size: 7/8-inch - Width: 27.5-inch - Rise/Reach: 8.25-inch - Type: BMX - Material: Steel
Light weight, comfort, and strength: the new SL-70 Ergo is the ultimate handlebar for long days in the saddle. The SL-70 Ergo combines the flat bar top shape of the beloved Contour SL bar with numerous modern features sought after by riders and pro bike fitters. The SL-70 Ergo sports a 70mm reach and 128mm drop. The short 70mm reach has been a popular choice in recent years, as it allows bike fitters flexibility in achieving a comfortable position without sacrificing steering control. The drop utilizes a variable radius, allowing for multiple hand positions and deeper movement into the drop. As a result, reach to the brake lever is shorter. A 3° backsweep on the flat tops keeps the wrist in a comfortable position, essential for long days on pavement or gravel, while the 10° ramp angle provides a smooth transition to modern shifter hoods. Brake and shifter housing is elegantly hidden along the underside of the bar. - Updated distinctive Zipp cosmetics - Unidirectional carbon built for stiffness, comfort, and light weight - Flattened top shape with 3° backsweep for comfort - Variable radius drop for multiple hand positions and deeper movement into the drop. - Lifetime warranty
On today's road bikes, silver stands out amid the sea of stealthy black color schemes. This time-honored handlebar color is available on the Zipp Service Course 70 Ergo handlebar. The Service Course lineup provides options to match every rider with a high-performance, precise fitting bar. The Service Course 70 Ergo packs a powerful punch of everything you'd want in a bar — a design based on feedback from pro bike fitters and riders, an ergonomic top section, and a price you'll love. - 6061 aluminum for low weight and durability - 70mm reach and 128mm drop for a short-low position - Flattened top shape to better fit the hand - ISO 4210 compliant
On today's road bikes, silver stands out amid the sea of stealthy black color schemes. This time-honored handlebar color is available on the Zipp Service Course 70 XPLR, our newest drop-bar offering. The bar's moniker, XPLR, exemplifies the desire to explore the world with an expanded definition of cycling on a drop bar bicycle — from paved roads to gravel, mud, dirt, and even singletrack. The Service Course 70 XPLR helps you go faster by placing your body, starting with your hands, in an optimal "comfort zone" position for hours of rough riding over mixed terrain. Whether on a two-hour training ride from home or a 200-mile gravel adventure, today's riders demand more of their cockpit: comfort, control, and the ability to carry what they need. We met these needs by creating a bar with shallow and wide drops while focusing on two crucial metrics — outsweep and flare. - Bar drops provide a wider, balanced, and secure position with drops that are about 6cm wider than the hoods position for technical or intense riding. - The 70 XPLR features an ergonomic top with an extended 100mm clamping area for computer mounts, aero-extensions, bags, and whatever else you may need for the long haul. - Reach: 70mm - Drop: 115mm
The Service Course SL-80 provides comfortable and efficient positions on the bar tops, brake hoods, or down in the drops. The bar allows a neutral wrist position on the drops and a flat brake-hood transition. This minimizes the need for up-rotated bars. Drops are angled outward by 4 degrees, reducing wrist strain. Named after its 80mm reach to bring the hoods and control levers back where you want them. The ergonomic 125mm drop places the angled drop position where you can easily reach it while maintaining a neutral wrist angle. The SL-80's rounded bar top is clip-on compatible. Forged from lightweight 7075 aluminum. - Distinctive Zipp cosmetics - 7050 Aluminum - 80mm reach/125mm drop designed to fit a large number of riders - Clip-on compatible - Lifetime warranty
$78.00 - $80.00
Whisky's No.7 12F is their most versatile drop bar. It's equally at home on tarmac, gravel or twisty cyclocross courses. From touring to racing, this modern bar is a great addition to almost any bike in your stable. The comfortable 12-degree flare provides excellent control and comfort, especially off-road, or in challenging conditions. A semi-compact design offers seamless transitions between positions. Available in a complete size range, this bar is a perfect fit for any rider. - 7050 Alloy - 282g (42cm) - Drop: 116mm - Reach: 68mm - Flare: 12° - Measured Center-to-Center at the levers
Whisky's No.7 24f is designed for comfort and control in challenging situations. Specifically aimed at long distance touring, gravel, or off-road pursuit, the 24-degree flare offers huge control from the drops. This thoroughly modern drop bar is the perfect match to your off-road tourer, monstercross bike, or get-rad CX rig. The 24f’s sleek design offers seamless transition between positions. Available in a broad size range, there’s a width to perfectly fit your needs. - 7050 Alloy - 282g (42cm) - Drop: 116mm - Reach: 68mm - Flare: 24° - Measured Center-to-Center at the levers
Whisky's No.9 Flat Bar keeps your weight lower and more forward on the bike for a more aggressive riding position. It’s wide, sleek, and tested to the highest standards to deliver hours of reliable trail riding. Trimmable ends allow you to really dial in your fit to keep you comfortable every time your tires hit the dirt or snow.
Whisky's No.9 Riser Bar features a 25mm rise and a 5-degree upsweep to offer a slightly more upright riding position that increases control and comfort. It’s wide, sleek, and tested to the highest standards to deliver a ride you can trust mile after mile. Trimmable ends allow you to really dial in your fit to keep you comfortable every time your tires hit the dirt or snow.
$78.00 - $80.00
The No.7 6F is our take on a modern performance drop bar. Sleek, ergonomically designed curves end in a wrist-friendly 6-degree flare at the drops. This gives just enough space to open your chest and provides forearm clearance in the drop position. This modern design offers seamless transitions between positions. The 6F features a slightly deeper drop than our 12F and 24F handlebars. Available in a complete size range so you can dial in your fit.
The No.9 35.0 Mountain Carbon Handlebar is designed and built for the most extreme trail and all-mountain riding. The oversized stem clamp adds to front-end stiffness for precise input, while the carbon construction provides vibration damping in a lightweight and durable package. - Unidirectional carbon fiber construction - 35mm stem clamp - 8 degrees of backsweep with 5 degrees of upsweep - Trimmable ends, made easy with graphic markings - Rated to ASTM Condition 4 for extreme off-road riding
Occupying a class all its own, our Winston Handlebar is a performance carbon mustache bar loaded with versatility and flare. Featuring a 25mm rise and 73-degree backsweep, it offers compatibility with road, mountain, and bar-end controls. Pretty enough to punch up commuter rigs and sport touring bikes alike, it's built tough to handle everything from rough, off-road conditions to long rides in the country. Comfortable in both the drop and riser positions, the unique and multi-functional Winston is sure to inspire upgrades and eye-catching custom builds. - Compatible with road, mountain, and bar-end controls - Tested to ASTM 3 - 90mm clamping area to fit Salsa Anything Cradle - Can be ridden in up or down position - Unidirectional carbon fiber construction - Weight: 250g
WeThePoeple Pro rider, Dan Kruk, is somewhat of a connoisseur of handlebars, so it is only right that he have his own signature model. Named after his home town in Wisconsin, the Stallis bar is built to withstand Dan’s all-out savagery on a bike and comes in both regular 22.2mm and 25.4mm oversize clamping options.
$12.98 - $15.99
This mid-rise handlebar provides smooth lines and pure comfort - Black powder coat - 1"(25.4mm) clamp, 5.25" rise, 27" wide - Handmade in Maysville, Kentucky
This classic touring handlebar is great for bicycle restorations or for adding a touch of traditional class to any bike - 1"(25.4mm) clamp, 2.5" rise, 23.75" wide - Handmade in Maysville, Kentucky
With multiple geometry options to choose from, Wald's Steel Handlebars offer great options for riders looking to accessorize their bike or find a replacement option that feels comfortable. - Chrome finish - Made in the USA - Weight: 372g - Lever Compatability: Mountain 22.2mm
With multiple geometry options to choose from, Wald's Steel Handlebars offer great options for riders looking to accessorize their bike or find a replacement option that feels comfortable. - Chrome finish - Made in the USA - Weight: 726g - Lever Compatibility: Mountain 22.2mm
Velo Orange's Milan bar is so named because it's a great bar for converting an old Italian racing frame with a short top tube. Actually, it's great for converting any frame with a short top tube into a city bike. Folks who like a more aggressive position on a city bike will like it, too. The width is about 570mm and reach is 110mm; there is around 25mm (approximately one inch) of rise. The grips sweep back about 35 degrees, and the grip area is about 170mm long. The clamp area is 25.4mm. The material is polished aluminum alloy. Milan bars work with regular MTB (22.2mm) grips, brakes, shifters, 22.2 inverse brake levers, etc., but not bar-ends.
Remember those great Belleri Porteur bars from France? Of course Belleri is long out of business, but those handlebars are still sought-after. So, Velo-Orange decided to make their own Porteur bars. They are 480mm wide; reach is 140mm. The grip area is about 130mm, and they have about 15mm of rise or drop. The clamp area is 25.4mm. The quality and polishing are very nice. The transition from the grip to the curve on the originals was a bit abrupt; The Velo-Orange version has a gentler transition. The curves on both versions are fuller and, we think, prettier than the somewhat similar Champs Elysées bars used on the old Herse bikes. These bars are available in two tubing diameters, 23.8mm road-sized and 22.2mm mountain bike-sized (clamp area is 25.4mm on both): - 22.2mm diameter (MTB-size) bars accept MTB brake levers and clamp-on shifters. They do not work with bar-end shifters. The only inverse levers that work are Dia Compe levers in the 22.2mm size. - 23.8mm diameter (road-size) bars accept standard inverse brake levers, standard bar end shifters, and 23.8mm city brake levers. In short, anything made for road bars fits. They do not accept MTB levers or shifters.
Velo Orange's Tourist bar is a "North Road" style bar rendered in polished aluminum alloy. It's similar to the bars used on many classic British roadsters. The clamp area is 25.4mm in diameter. The width is 570mm and the reach is 180mm; it has about 70mm of rise. They sweep back about 60-degrees, and the grip area is about 160mm long. The Tourist accepts regular MTB (22.2mm) grips, brakes, and shifters, but not inverse levers or bar-end shifters.
The Atmos 7k aluminum riser bar series feature a 9° backsweep and 760mm width that is trimmable by 30mm at each end for a possible width of 700mm. The bar is available in 3 rise variants: 0mm, 10mm and 20mm. Made from tough 7050 Lightweight aluminum, the bar weighs just 250g at full width. - 760mm wide - Wide to start and trimmable by 30mm each side - Made from tough 7050 lightweight aluminum SPECIFICATIONS - Type: Riser - Application: XC - Clamp Diameter: 31.8mm - Width: 760mm - Backsweep (degrees): 9
TruVativ is proud to announce the TRUVATIV CoLab Series, a collection of bars specifically engineered to match the demands of each signature athlete's discipline and riding style — and to enhance each rider's cockpit interface. - Upsweep: 5° - Backsweep: 9° (760mm bars) - Backsweep: 7° (all other bars)
You say you want a wide, stiff, strong, championship-winning design? Here you go. The new Descendant DH bar borrows from a rich championship-winning heritage, and adapts it to today’s aggressive courses and riders. Descendant DH bars are the command center of cornering control. - Stiff, precise, and super-wide - Made with tough 7050 alloy - Descendent geometry from TruVativ's best enduro rider’s input - Backsweep: 9° - Upsweep: 5°
Page 1 of 9 Next page